AILI® DC 0-90V 0-500A Voltage Current AH Capacity Battery Monitor Capacity BatteryTester Volt Meter Ampere

I installed this meter in my travel trailer with a 100W solar panel. I've taken it on a few trips and I really like this meter, especially for the price. I think it does all that I need and can't see why I would spend $150-$300 for one of the better known power meters. Installation took some work, but no more than for any similar power meter. I use this meter all the time and never look at the display of the solar controller. I always know how much power I have in my battery and what charge/discharge is happening. Cons: The current meter has a light that indicates if it is charging (off means it is discharging), but does not indicate positive or negative, so you kind of need to look to determine if the current is flowing in or out of battery. Most of the time, you will know (i.e. the sun is out and the panel is pumping 4 or 5 Amps into the battery). I had to extend the wires of the current and voltage sensor, but home depot has shielded twisted pair that seemed to work just fine. The wiring diagrams provided with the unit have a couple of issues: 1) wiring the meter as indicated gives a resulting meter reading that does not include the meter power consumption - it's pretty small, so not a big deal. 2) The ground for the meter is electrically connected to one side of the current sense resistor on the sensing board - this isn't clearly explained anywhere, so you could hook it up and have all of the current pass through sensor board and you would get 0 Amps on the meter and maybe even fry the circuit board trace. Just follow the wiring diagrams and you'll be fine. Pros: I always have a really good idea how much power is in my battery - just like a gas gauge for your battery. I can easily tell how much current is coming or going from the battery - much more useful than the display on the solar charge controller which only tells you about the current from the solar panel. This functionality should be included as an option in all charge controllers IMO. I can figure out how much current all of the appliances in my rig consume.

Connected per the instructions. The unit is non responsive, 12 volts are measured at the interface board screw lugs all the way to the display board solder pins. This means that 12 volts is making it through the cable to the display. Connected direct to a battery, and still dead. A replacement has been requested. We'll see. Heard back from the seller, was asked to connect voltage to the alternate terminals (V-Ext) although this worked, the unit should be powered from the main (V-in) terminals. Was asked to connect to both at the same time, I don't think this is satisfactory. A replacement unit was sent, installed, and the performance is better.

100% OK!!!

Would not measure current out of the box. I have connected it as described in the instructions for a "two wire system" ( which really takes four wires ). It reads voltage fine and is very close to my voltmeter. However, when I use an 8 Ohm load ( 1.5A on 12V ), I get 000.0 on the current display. My own ammeter reads 1.46A . I went through the settings, and the current "multiplier" was set to 20 rather than the "default" of 200 mentioned in the instructions. After changing that to 200, I see no difference. I am an analog design engineer, so I think I hooked it up correctly. I also noted that the shunt was bent ( definitely not from shipping - the packaging was good ). However I cannot see how that could make much difference. If anything, I would think it might increase the resistance of the shunt and make the current reading too high. The shunt is labeled "200A / 75mV " so it looks like the correct shunt. EDIT: I did a factory reset, and now it appears to be working. However, the current multiplier had to be set to 18 ( the value after reset was 20, so I think the instructions are wrong when they say the default is 200 ) to match my current meter. Perhaps the bent shunt indeed has too much resistance. ALSO: From my measurements, this device cannot measure negative current. I see no claim for that by the seller, but I expected it would based on the other products they sell. As I wanted to use this as a battery monitor, I see now that I bought the wrong product, so I have just ordered the one designed for that use, not sure how I missed that.

Seems like some are ok, but mine is very inaccurate. I tried calibrating it multiple times, and it would get down to "0%" before it was at 0%, which messes it up to no end. My battery system is 112AH. I tried setting the value to lots of different values, it always eventually ends up at 0%. All my other sensors agree on AH/KW usage ... this is the one outlier.

The unit that I received displays the voltage and current draw amperage correctly, but it does not seem to notice the amperage put into the system by my solar controller / charger. Thus after a few days it thinks that the battery is completely drained even though the voltage indicates that the battery is full. I have searched in vein trying to find a support email address for this manufacturer or seller. I'd love to contact someone (seller or manufacturer) or have them reach out to me to see if I've made a wiring mistake or if I've received a faulty unit.

Accurate and easy to read used on a solar system gives all the info you need

This is a great addition to my Solar Power System. It measures the amount of power going into and out of the battery system. It's perfect for my needs.

Had installed the LCD type, and could not read the display unless I was face to face with them. These, I can read from far away. Manual a bit challenging to decipher.

I'm happy with this meter readings were accurate out of the box and for my needs it reads amps being used and amps charging the battery good product for the price

I don't mind reviewing this item but I cannot do it right now. Unforeseen circumstances will delay installation of this device for another week or two. Sorry. A