【2026 Upgraded】 3392519 Dryer Thermal Fuse WP3392519 Universal Replacement Fit for Whirlpool Kenmore Maytag Dryer Replaces AP6008325 3388651 694511 WP3392519VP 80005 G4AP0500 by Romalon, 3-Pack

These Thermal Cut-off Fuses worked perfectly for my Kenmore 700 series Dryer. Make sure to verify your exact Dryer Model because my Fuse was behind the (not behind the back Dryer panel) Lower Front Panel which is the only panel that needs removed. Also unlike a YT Video that shows the Front Blower & Drying Tub/Belt needs removing 1st, the job is "Much Easier" if done in the following (approx. time approx. 1.5 hrs.) manner. 1.) Make sure the Dryer Power Cord is unplugged. 2.) "Pull" the Dryer away from the Wall & Remove the Dryer Vent Hose from the Dryer Exhaust Vent . MAKE sure to clean the (if needed) Dryer Exhaust Vent & Vent Hose of any seen Lint. 3.) Now remove the Lower Dryer Front Panel & Gently lay the Dryer on it's "LEFT" side. You will then have easy access to the Thermal-cut Fuse that can be seen from Rt-side (with said Panel removed) opening. 4.) Using the proper Tools , remove the "2" Wire Connectors that are attached to the "2" Thermal Fuse Tabs paying close attention (I marked the Front wire with a Permanent Marker) to their orientation for proper reattchment later. 5.) Using a 1/4" Ratchet w/short "Magnetic" extension or similer & a small Socket that fits the "Single" Attachment Screw ...remove said Screw & then pull out/remove the "Blown" Thermal Fuse. 6.) Now, install the new Thermal Fuse with a short Magnetic Extension Socket ...being careful "Not" to drop the single Thermal Fuse "Attachment Screw" down into the Dryer Cabinet. 7. Now, before reattaching the Dryer Vent Hose ...push your Dryer back closer to it's Electrical Wall Outlet & plug it in to check "IF" the Dryer runs now. If it does then unplug the Dryer again & pull it out from the Wall again to reattach the Dryer Exhaust Hose. 8.) Finally ...Pop your lower Front Panel back on & reposition your Dryer to it's normal running location & plug the Power Cord back into the Electrical Outlet.

Cheap and effective. Fixed my drier. No issues

Fit well, worked fine.

Check this first if your dryer doesn’t work. I replaced everything and forgot about this . Wouldn’t you know it turned out to be this thermal couple .

Perfect fit, fixed our dryer, the wife is pleased!

This part works as advertised. It is a bit difficult to install. This is the third or fourth one i have replaced. They were from different Amazon sellers. Cheap part that does not last. Glad I don't have to pay over $100 for a service call to replace a $2 part.

This was the cheapest way to fix 90 percent of the causes for dryer failure. The fuse burns out because your dryer needs a good cleaning. Most times the impeller for the exhaust gets plugged with so much lint it can barely turn causing the area where the fuse is mounted get hot enough to melt, this stops unit from catching fire.

This was easy to install and a perfect fit. I've seen a few negative comments about life and durability. I have only had this installed for about a week, but I wonder about whether those comments consider what this is for. The thermal fuse for a dryer is designed for one purpose - to fail and stop the dryer when it gets too hot so it won't cause a fire. Typically that means, if the fuse blows, there is something wrong that needs to be fixed. That might mean the ducting to outside needs to be cleaned, but it might also mean that the dryer's internal ducting is clogged. Having to replace the thermal fuse is a wake-up call to check for the real problem, like the internal filter in this photo, which (1) requires some venting disassembly and (2) is only one of the internal areas that was clogged.